a series of FM sound chips which were very popular in DOS land. it was so popular that even Yamaha made a logo for it!
essentially a downgraded version of Yamaha's other FM chips, with only 2 operators per channel.
however, it also had a drums mode, and later chips in the series added more waveforms (than just the typical sine) and even a 4-operator mode.
the original OPL (Yamaha YM3526) was present as an expansion for the Commodore 64 and MSX computers (erm, a variant of it). it only had 9 two-operator channels and drums mode.
its successor, the OPL2 (Yamaha YM3812), added 3 more waveforms and was one of the more popular chips because it was present on the AdLib card for PC.
later Creative would borrow the chip to make the Sound Blaster, and totally destroyed AdLib's dominance.
the OPL3 (Yamaha YMF262) added 9 more channels, 4 more waveforms, rudimentary 4-operator mode (pairing up to 12 channels to make up to six 4-operator channels), quadraphonic output and some other things.
afterwards everyone moved to Windows and software mixed PCM streaming...
10xx: set AM depth. the following values are accepted:0: 1dB (shallow)1: 4.8dB (deep)11xx: set feedback of channel.12xx: set operator 1 level.13xx: set operator 2 level.14xx: set operator 3 level.15xx: set operator 4 level.16xy: set multiplier of operator.x is the operator (1-4; last 2 operators only in 4-op mode).y is the new MULT value..17xx: set vibrato depth.0: normal1: double18xx: toggle drums mode.0 disables it and 1 enables it.19xx: set attack of all operators.1Axx: set attack of operator 1.1Bxx: set attack of operator 2.1Cxx: set attack of operator 3.1Dxx: set attack of operator 4.2Axy: set waveform of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y is the value.30xx: enable envelope hard reset.50xy: set AM of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y determines whether AM is on.51xy: set SL of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y is the value.52xy: set RR of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y is the value.53xy: set VIB of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y determines whether VIB is on.54xy: set KSL of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y is the value.55xy: set SUS of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y determines whether SUS is on.56xx: set DR of all operators.57xx: set DR of operator 1.58xx: set DR of operator 2.59xx: set DR of operator 3.5Axx: set DR of operator 4.5Bxy: set KSR of operator.x is the operator from 1 to 4; the last 2 operators only work in 4-op mode. a value of 0 means "all operators".y determines whether KSR is on.this chip uses the FM (OPL) instrument editor.
when two channels are joined for 4-op mode, the channel bar will show 4OP on a bracket tying them together.
the following options are available in the Chip Manager window:
additionally, in OPL3: